PTM7950 40 x 80 x 0,2 mm Phasenwechsel GPU Thermopad, JOYJOM Hochleitfähiges Silikonfett 8,5 W/mK CPU Wärmeleitpaste für PS5 Steam Deck CPU GPU SSD M.2 Laptop

works as expected. highly recommended. temperatures went down ~20-25 degreees

The real deal. Dropped my hot spot temps on my 4080 super 40 degrees. Yes, you read that right. Hotspot was hitting 110c bc Asus is a garbage company, and corrupt to their core. After only a couple hours of work, hotspot is only hitting 70c. Core temps dropped ~13 degrees. Fans finally running slow and quiet.Asus wanted me to tear my PC apart for a month while they "repaired" the GPU, but really all they were going to do is put the same cheap thermal paste on the GPU in hopes that it would be another 6 months before it happens again when the warranty had expired.Whoever put this kit together really went the extra mile. Not only is this the real deal, they provide you with all the tools you'll need to work with it. They've really thought it thru. In case it's not obvious, the little green tabs are for peeling away the plastic film on both sides. Stick one of the green tabs to each side, with the line between the transparent and green lines up exactly with a corner/edge.

Finally solved my problem on my old laptop that always reaches +95 degrees when gaming and +50degress at idle. Now, after using this, my idle is at 38degrees and gaming at 88degrees.

Habe mir dieses Thermopad gekauft da meine Red Devil RX 6800 XT immer eine 25-30° höhere Hotspot temperatur hatte als die normale Temperatur.Man muss sagen dass das Auftragen für jemanden der das zum ersten mal macht etwas fummelig ist - ich habe mir extra dafür eine kleine Pinzette zuvor gekauft und für mich war es das auf jeden Fall wert.Nun gut was sagen die Temperaturen nach den Wechsel auf die PTM7950?Cyberpunk 2077 1440P alles auf Max, kein Raytracing - GPU ist Übertakted und zieht ca. 330W.Voher: GPU Temp: 75° Hotspot: 97-105°Nacher:GPU Temp: 70° Hotspot: 85-89Ich bin wirklich überrascht wie gut Thermopads geworden sind, damals hieß es ja quasi immer nur das Thermopads soviel schlechter seien als Paste, aber diesen Unterschied hätte ich wirklich nicht erwartet.Achtung: Das Thermopad brauch einige Zeit(Bei mir waren es 2-3 Tage) mit Last bis man die wirklich richtigen Temperaturen sehen kann, es muss sich quasi etwas verflüssigen und sich besser auf den Chip verteilen was evtl. etwas dauern kann - allerdings hat man hier den Vorteil das sich die Temperatur nicht mehr verschlechtern wie bei Wärmeleitpaste nach einigen Monaten, für die Langlebigkeit auf jeden Fall top!

Took a risk buying this, there were 3 issues:- Product listing has "Brand: JOYJOM" but the paste should have been made by Honeywell.- Cost (I paid £25.46) is far higher than any thermal paste I know of.- Posted from China or USA (I can't tell), not sure how I'd get a refund if it's not right.I used it to re-paste my laptop Legion 5 Pro 2021 16ACH6H because the processor reached 104°C using Arctic MX4.It worked as you can see in my screenshot attachments (they were running Cinebench r23) and reducing the temps in some of my games by up to 20°C.They provided provided tools but I think they were inappropriate, why do I need a screwdriver and a brush? They should have provided a tweezer instead to remove the plastic covering the pad.

I am having a hard time accepting how good this actually is. I have a G513QU gaming laptop which, unfortunately, was one of the serial numbers with the faulty liquid metal solution and after a year or so it had pumped out enough that the clocks were not boosting to nearly the speeds that it was when it was new. I decided to crack it open and replace it myself instead of sending it back to Asus RMA as I know Asus has made it their life's mission to make the RMA process as horrible as possible.I opened the laptop up and took out the liquid metal and the faulty barriers. I prepped the SMDs around the dies for liquid metal and got to the point where I wasn't confident on making my own barrier so I just put paste on it to see how that went - it went poorly. My temperatures were high and clocks were low. I then found out about PTM7950 after doing some research and decided to give it a go.This stuff was pretty hard to work with before I figured it out so expect a trial run before you actually get it right. I bought a cutting mat, measuring tool, and a craft knife to get it done correctly. I measured the dies and then cut accordingly. Getting on was a bit tricky but once you learn to use tweezers to set it properly on the die and lift up from the corners to get the film off it actually is not hard to work with.Once it was on I put the laptop together and was shocked at how good my temperatures were. I added some spacers to increase the mounting pressure and with those plus the PTM7950 I am getting better temps than I did with the original liquid metal application. Now, obviously the increased mounting pressure is doing some work here but I had that going with the normal paste and my temperatures weren't even close to as good as with the PTM7950. Now, my clocks boost to max speed and even though the CPU is designed to boost to 95c and hold it actually only get to about 92c which is absolutely bonkers. The GPU is doing great as well and there is zero throttling on the laptop. I was able to pass a 20 minute time spy stress test which I was unable to do with the paste application. This stuff is absolutely amazing.One last thing to note. I did two applications where one had the PTM7950 completely covering each die and the next I uses a bit less because there was a lot of pump out meaning that there was too much used. Well, covering the full die was better as I guess the pumped out bit can catch heat coming off the sides and pipe that to the heatsink so I would definitely cover the entire surface area of the die if you're doing direct die cooling.One last thing, in the videos of people using the actual Honeywell PTM7950 the pads are a bit thicker (0.25 vs 0.2 mm) and the colour is blue versus the grey of this. I was skeptical that this isn't PTM7950 because of that and I don't know what it actually is but it cools significantly better than good thermal paste so I am guessing it is a knockoff but still the same formula.A bit expensive but totally worth it.

This product seems to be non genuine PTM7950, as the temperatures this product provides when applied do not line up with these of tests with real PTM7950.I applied it twice with some testing time in between, to make sure it wasn't wrongly applied, but the temperatures were worse all around.I tested them on my steam deck, and later applied normal thermal paste, which should perform worse, but gave me 5 to 10°C less than this product.I can't recommend this, as it does not appear to be the real PTM7950.

Nutze es mit einem 1340p der im alltäglichen gebrauch 12°C kühler läuft. Die Größe des Pads reicht für locker 5 dieser Geräte. Werde es noch mit einem 5800x testen.